2.67 CORRUGATED |
|
 |
| ROOFING: POSITIVE LOADS | ||||
| SPAN | Uniform Loads, PSF |
SERIE | ||
| FR200 | FR300 | FR400 | ||
| SINGLE | 20 | 3'9" | 4'1" | 4'3" |
| TWO | 5'1" | 5'6" | 5'8" | |
| THREE | 4'8" | 5'1" | 5'3" | |
| SINGLE | 25 | 3'6" | 3'10" | 3'11" |
| TWO | 4'8" | 5'2" | 5'3" | |
| THREE | 4'4" | 4'9" | 4'10" | |
| SINGLE | 30 | 3'3" | 3'7" | 3'8" |
| TWO | 4'5" | 4'10" | 4'11" | |
| THREE | 4'1" | 4'5" | 4'7" | |
| SINGLE | 35 | 3'1" | 3'5" | 3'6" |
| TWO | 4'2" | 4'7" | 4'8" | |
| THREE | 3'10" | 4'3" | 4'4" | |
| SINGLE | 40 | 3'0" | 3'3" | 3'4" |
| TWO | 3'11" | 4'5" | 4'6" | |
| THREE | 3'8" | 4'1" | 4'2" | |
| SINGLE | 50 | 2'9" | 3'0" | 3'1" |
| TWO | 3'2" | 4'1" | 4'2" | |
| THREE | 3'5" | 3'9" | 3'10" | |
| ROOFING: NEGATIVE
LOADS Fasteners required at every other corrugation |
||||
| SPAN | Uniform Loads, PSF |
SERIE | ||
| FR200 | FR300 | FR400 | ||
| SINGLE | 20 | 3'9" | 4'1" | 4'3" |
| TWO | 5'1" | 5'6" | 5'8" | |
| THREE | 4'8" | 5'1" | 5'3" | |
| SINGLE | 25 | 3'6" | 3'10" | 3'11" |
| TWO | 4'8" | 5'2" | 5'3" | |
| THREE | 4'4" | 4'9" | 4'10" | |
| SINGLE | 30 | 3'3" | 3'7" | 3'8" |
| TWO | 4'5" | 4'10" | 4'11" | |
| THREE | 4'1" | 4'5" | 4'7" | |
| SINGLE | 35 | 3'1" | 3'5" | 3'6" |
| TWO | 4'2" | 4'7" | 4'8" | |
| THREE | 3'10" | 4'3" | 4'4" | |
| SINGLE | 40 | 3'0" | 3'3" | 3'4" |
| TWO | 3'11" | 4'5" | 4'6" | |
| THREE | 3'8" | 4'1" | 4'2" | |
| SINGLE | 50 | 2'9" | 3'0" | 3'1" |
| TWO | 3'2" | 4'1" | 4'2" | |
| THREE | 3'5" | 3'9" | 3'10" | |
| SIDING: WIND LOADS Fasteners required at every other corrugation |
||||
| SPAN | Uniform Loads, PSF |
SERIE | ||
| FR200 | FR300 | FR400 | ||
| SINGLE | 20 | 4'9" | 5'2" | 5'4" |
| TWO | 6'5" | 7'0" | 7'2" | |
| THREE | 5'11" | 6'5" | 6'7" | |
| SINGLE | 25 | 4'5" | 4'10" | 4'11" |
| TWO | 5'11" | 6'6" | 6'8" | |
| THREE | 5'6" | 6'0" | 6'2" | |
| SINGLE | 30 | 4'2" | 4'7" | 4'8" |
| TWO | 5'3" | 6'1" | 6'3" | |
| THREE | 5'2" | 5'7" | 5'9" | |
| SINGLE | 35 | 3'11" | 4'4" | 4'5" |
| TWO | 4'6" | 5'10" | 5'11" | |
| THREE | 4'11" | 5'4" | 5'6" | |
| SINGLE | 40 | 3'9" | 4'1" | 4'3" |
| TWO | 3'11" | 5'6" | 5'8" | |
| THREE | 4'6" | 5'1" | 5'3" | |
| SINGLE | 50 | 3'6" | 3'10" | 3'11" |
| TWO | 3'2" | 4'9" | 4'9" | |
| THREE | 3'7" | 4'9" | 4'10" | |
- Critical bending moment at actual panel failure
- Flexural stiffness
- Pullover force per fastener of the panel section.
Table values are based upon:
- Roofing: Deflection l/60, FOS 2.5+, 1.88-
- Siding: Deflection L/30 FOS 1.88
|
Download a printable Adobe Acrobat version of this page |
Each span shown in the load/span tables represents the most conservative span derived when the panel is assessed using the following parameters:
Design Parameters
- Critical bending moment at actual panel failure;
- Flexural stiffness factor, EI, (where
E is the flexural
modulus of elasticity and I is the moment of inertia of
the panel section); and - Pullover force resistance per fastener.
Panel Roofing:
Positive Loads: Deflection: L/60, FOS:2.5
Negative Loads: Deflection: L/60, FOS: 1.88
Panel Siding:
Wind Loads: Deflection: L/30, FOS:1.88
Roof Deck:
Dead + Live Loads: Deflection: L/180, FOS:2.5 Uplift Loads: Deflection: L/18000, FOS:1.88
The load/span tables are to be used as a guide only as specific environmental conditions are not considered.
Specific applications should be verified by a registered Professional Engineer.